If your microwave breaker keeps tripping, the fault is likely in your microwave itself. A bad magnetron, internal circuitry damage, or blown fuses are some possible causes. It is best to have your microwave repaired rather than try to fix the tripping breaker yourself, because repairs create a fire hazard and potential electrocution risk. Also, the cost of repairs can potentially be more than buying a new unit.
Possible Reasons Why a Microwave Breaker Keeps Tripping
If your microwave keeps tripping the circuit breaker, it’s most likely caused by an overload or a circuit problem. You may have a short in the cord, a problem with the receptacle or the breaker panel, or the microwave itself may be causing the problem. Whatever the reason, it’s a good idea to check the breaker panel and the microwave for damage.
If you’re unsure why your microwave is tripping the circuit breaker, it may have a faulty magnetron, damaged internal circuitry, or blown fuses. To determine if your microwave has these problems, take a look at the breaker’s label.
When a circuit breaker trips, it means that an overload of amps has occurred. The breaker is there to protect you from a dangerous overload. This overload can damage your microwave, overheat the wiring, or even cause an electrical fire. Therefore, you should avoid overloading circuits by using multiple appliances at once.
If you’re unable to fix the problem yourself, call a licensed electrician or repair shop. However, if you are unable to fix the problem, you could cause more damage to your home or injury to yourself. If you’re unsure about how to repair a microwave, it’s important to consult a qualified electrician.
Sometimes, a microwave’s safety latch mechanism can be the problem. If the latch mechanism breaks, electromagnetic waves will escape, triggering the circuit breaker. To find out if the latch hooks are broken or faulty, you can test the latch mechanism with a multimeter in Ohms O mode. Make sure you disconnect the appliance from power before testing.
A tripped circuit breaker could also be causing an overload, which happens when there’s too much electricity being drawn by a single device. An overload can be caused by loose wires or corroded wires. Another reason a circuit breaker keeps tripping is numerous items on the same circuit. A hair straightener, for example, can be plugged into the same circuit as large appliances.
If the problem persists after you’ve followed these steps, you might need to replace the capacitor in your microwave. However, it’s not a good idea to try to fix the capacitor yourself. This is a dangerous process, and you should use an electrically insulated tool for the task. Unless you have experience in electrical work, it’s best to hire a professional.
Checking the Door Latch
If the circuit breaker on your microwave keeps tripping, you may be having problems with the door latch switch. You can check the door latch switch by placing a multimeter probe on the microswitch terminals and seeing if continuity is present. If not, you may need to replace the switch.
If the circuit breaker keeps tripping, you may need to replace a faulty component. One of the most common causes is a faulty door latch switch or door latch hooks. If they are faulty, you need to replace the door latch switch unit or replace the door latch hooks. To test the door latch switch, disconnect the power source and test it. If it still trips the circuit, the door latch switch or hooks may be broken.
If you are not comfortable performing repairs yourself, seek assistance from a professional electrician. Performing DIY repairs can result in physical injury or property damage. It is recommended to get a professional electrician to fix mislabelled circuit breakers. You should also be aware that switching it incorrectly can damage the electronics. To avoid mishandling the circuit breaker switch, make sure to use the correct breaker label for your microwave.
If you are unable to open the door of your microwave, the first step is to check the door latch. The door latch is also known as the “hook” or “latch” and is responsible for activating the door switch when the door is closed. To find the location of this latch, you need a screwdriver, a pair of rubber gloves, and a multimeter.
The door latch is one of the most common causes of microwave circuit breakers to trip. It is a simple mechanism that keeps the door closed, but it can also cause the circuit breaker to trip when it is opened. Check the door latch switch to determine the cause of the circuit breaker trip.
Checking the HV Diode
If you’ve ever had trouble with your microwave’s breaker tripping, it’s a good idea to check the HV diode. This device is part of the high-voltage circuit that supplies power to the microwave. If it’s tripping often, this component should be replaced as soon as possible.
To test the HV diode, unplug it from its power source. Do not try to plug in the microwave with the cover off. It may still be charging the HV capacitor. However, this does not necessarily mean the microwave is still generating microwaves.
If the diode has been tripping for a while, try to isolate it with a 9-volt battery and use a resistance meter. If the resistance remains high or never changes, the diode may be shorted or stuck open. It is important to test the resistance at both ends of the diode to see if it’s increasing or decreasing.
If the HV diode is not the cause, then the fault could be in the microwave itself. It could be a bad magnetron or damaged internal circuitry. It could also be a blown fuse. Attempting to repair a microwave can be dangerous. It can cause an electrical fire and a risk of electrocution. Besides, the cost of repairing a tripping microwave is usually higher than purchasing a new one.
Checking the Capacitor
If your microwave’s breaker keeps tripping, another likely culprit to blame is the capacitor. You can test the capacitor’s function by unplugging the appliance and using an electrically insulated tool to discharge it. If the discharge fails, it is likely that the capacitor is faulty and needs to be replaced. A multimeter is also essential to check the capacitor.
First, make sure you use electrically insulated gloves when working on your microwave. You should also ensure that you unplug the unit before any repairs. Another important precaution is to use insulated pliers to short-circuit the capacitor. Be sure to check your microwave’s warranty before starting a repair.
If the capacitor is defective, you may notice an electrical leak. Checking the capacitor is important if you can hear an intense noise when using the appliance. In some cases, a defective capacitor may cause a blown fuse. If this is the case, you should contact a professional electrician.
Another cause of a tripped microwave breaker is overload. When this happens, the circuit cannot handle the charge properly. If the circuit is too hot, you should unplug additional appliances that are using it. This should help you determine whether the problem is with the microwave itself.
If the problem persists, it is important to check the capacitor first. The capacitor is the component responsible for storing electrical energy and releasing it to a magnetron. If this component is faulty, the microwave will not work. As a result, you may need to replace it.
If the turntable motor is faulty, there are few remedies but replacing the turntable motor. But, this may require professional assistance if you do not have the necessary expertise. To do so, dismantle the microwave’s outer casing. Then locate the door latching switches and disconnect the connectors. Next, check the magnetrons and make sure they are not broken. Then, use a probe to measure the voltage.
Home Decor Advisor: Your Go-To Experts
For all your home appliance repair guidance, visit our Home Décor advisor blog. We post weekly with plenty of informative content to help keep you in the know when it comes to home décor and repair. Whether you’re looking for home improvement how-to guides, or décor inspiration, our experts have you covered.
Hi, there my name is William Lee and I am the founder of the DecorHomefFiner.com website. I am an expert DIY for bathrooms, living rooms, and kitchens. I am also a social helper which means I am helping people on social media about their homes.